- Available Formats
- Options
- Availability
- Priced From ( in USD )
- ?
- Immediate download
- $54.00
- Printed Edition
-
- Ships in 1-2 business days
- $54.00
- Printed Edition + PDF
-
- Immediate download
- $73.00
Customers Who Bought This Also Bought
![Astm D638 Pdf Free Download Astm D638 Pdf Free Download](https://tensilkut.files.wordpress.com/2009/05/tkiitemp21.jpg%3Fw%3D450%26h%3D337)
- FRPI Laminate Certification Manual, 2017 Edition
Priced From $285.00 - ASTM D2116-16
Priced From $48.00 - ASTM D2343-17
Priced From $48.00 - ASTM D1621-16
Priced From $48.00
Astm-method-d6304-pdf.pdf - Download as PDF File (.pdf). Download astm d4239 method b pdf PDF file for free. Download astm method e698 pdf PDF file for free.pdf. Table of Contents. ASTM Standards for Material Performance a. ASTM Standard 71216 -09 for Rehab of Existing Pipelines and Conduits b. ASTM Standard D638-14 for Tensile Properties. Standard Test Method for Tensile Properties of Plastics. 1 This test method is under the jurisdiction of ASTM Commttee D20 on Plastics. O D638-02a Determe the. ASTM D1238 - 13 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer.
About This Item
Full Description
1.1 This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.
1.2 This test method is applicable for testing materials of any thickness up to 14 mm (0.55 in.). However, for testing specimens in the form of thin sheeting, including film less than 1.0 mm (0.04 in.) in thickness, ASTM standard D882 is the preferred test method. Materials with a thickness greater than 14 mm (0.55 in.) shall be reduced by machining.
1.3 This test method includes the option of determining Poisson's ratio at room temperature.
Note 1:This standard and ISO 527-1 address the same subject matter, but differ in technical content.
Note 2:This test method is not intended to cover precise physical procedures. It is recognized that the constant rate of crosshead movement type of test leaves much to be desired from a theoretical standpoint, that wide differences may exist between rate of crosshead movement and rate of strain between gage marks on the specimen, and that the testing speeds specified disguise important effects characteristic of materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens, which are permitted by these procedures, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed.
Note 3:This test method may be used for testing phenolic molded resin or laminated materials. However, where these materials are used as electrical insulation, such materials should be tested in accordance with Test Methods D229 and Test Method D651.
https://yellowscrap184.weebly.com/garage-gothic-fonts-free.html. Note 4:For tensile properties of resin-matrix composites reinforced with oriented continuous or discontinuous high modulus >20-GPa (>3.0 × 106-psi) fibers, tests shall be made in accordance with Test Method D3039/D3039M.
1.4 Cle keygen free. Test data obtained by this test method have been found to be useful in engineering design. However, it is important to consider the precautions and limitations of this method found in Note 2 and Section 4 before considering these data for engineering design.
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Document History
Browse related products from ASTM International
Pdf Free Download For Windows 7
- ASTM International >By Sections and Volumes >Section 8 - Plastics >Volume 08.01 - Plastics (I): D 256 - D 2343
- ASTM International >By ICS Code >83: Rubber And Plastics Industries >83.080: Plastics >83.080.01: Plastics In General